Description: Up for sale here is this complete replacement lighting set for the Sansui 8080DB and 9090DB. You will receive: Six (6) snap-in cool white 360° LED fuse lamps (for the tuning dial and meters) One (1) wired 3mm 6v 70ma incandescent bulb (for the tuning needle)Seven (7) wired 5mm warm white LEDs (for the source lights and stereo light)Four (4) 3mm 6v 70ma lights with new grommets (for the watt meters) These are top-quality bulbs, and are the exact same ones I use when I rebuild Sansui gear. These are top-of-the-line lights--I love using them! These are all carefully selected for a reason. The new 360° LED fuse lamps look the best on the dial and meters--regular 3-LED fuse lamps tend to cause hot spots and make the dial look uneven. The original source and stereo lights are an oddball 7v 100ma value and the wired 5mm LEDs are the best way to replace them properly. The wired 3mm incandescent bulb keeps the needle looking original, and goes in easily. The little 3mm bulbs are perfect for the watt meters, and the old grommets will have dried out and cracked by now, so replacing the old grommets is very important. These are all plug-and-play, so no worries about adding resistors or anything. You will need a soldering iron, wire cutters, needlenose pliers, heat-shrink tubing (and something to heat it with), and a Philips screwdriver. This is a moderately complicated job, so it's not for a beginner! Be very careful not to damage the tuning dial cord when you're soldering! If you wrap the dial cord in aluminum foil ahead of time, that will help protect it. Replacing the tuning needle light is a bit difficult--you need to carefully pry open the little metal tabs that hold down the old wire, carefully remove the old bulb from the hole in the needle, put in the new bulb, then close up the metal tabs again. The replacement tuning needle LED wires are a bit shorter than the originals, so you may need to splice the wires, then cover them with either heat-shrink tubing or electrical tape. The original watt meter bulbs have little pieces of plastic sleeve on the wires, which you can reuse for the new bulbs. The watt meters are challenging to access--you'll need to open up the receiver from the front in order to get to them. I would strongly recommend reflowing all the solder joints for the tuning dial fuse lamps, since the solder joints will dry out from the heat causing dead or intermittent lighting. Please see my pictures for details. US shipping and handling is $5, and international is $18, no matter what quantity you buy. All my small parts are set up for combined shipping, so just use the "add to cart" feature and then check out all at once, and it will combine shipping. If you have any questions, please ask. Looking for more parts? I have power switches, feet, pushbuttons, top case screws, bottom screws, faceplate screws, white LED fuse lamps, blue LED fuse lamps, 6.3v bi-pin bulbs, 8v bi-pin bulbs, 12v bi-pin bulbs, wired 8v 60ma bulbs, new power cords, new main capacitors for the Marantz 1060/2230, wired Pioneer speaker plug replacements, new 630v yellow film capacitors at 38 different values, new 1200v yellow film capacitors at 15 values, a large variety of transistors for vintage stereo repair, new Wima film capacitors for stereo repair, new 250v yellow film crossover capacitors, and more. Just use "add to cart" on everything you want and then check out for combined shipping.
Price: 23 USD
Location: Milwaukee, Wisconsin
End Time: 2024-09-14T19:48:50.000Z
Shipping Cost: 5 USD
Product Images
Item Specifics
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 30 Days
Refund will be given as: Money Back
Brand: Sansui
